null

Drain Flood Protector (4 inch - Threaded Standpipe Model)

(No reviews yet) Write a Review
SKU:
FG-S-4F
Shipping:
Calculated at Checkout
  • Drain Flood Protector (4 inch Standpipe Model)
  • Drain Flood Protector (4 inch - Threaded Standpipe Model)
  • Drain Flood Protector (4 inch - Threaded Standpipe Model)
  • Drain Flood Protector (4 inch - Threaded Standpipe Model)
$43.95

Description

dn-floodguard-standpipemodel.jpg

The Drain Flood Protector Standpipe Model does not have a float, and is available for 3" and 4" drains. The standpipe models are recommended for more extreme or extended pressure situations. In the event of a backup, water rises up the inside of the pipe. The length of the standpipe can be made the length you determine you will need it to be to offer the best possible protection for your situation. Your standpipe height should be higher than the highest point of flooding elevation you have experienced.  Watch the Product Video for a lot of helpful information!

View and download Spec Sheet

 
 
floodguard-spmdiagram.gifHow The Standpipe Model Works
 
To install the 3" standpipe version, the Drain Flood Protector has a rubber gasket the standpipe is inserted into and both are then lowered into the drain pipe. The screws are fully tightened once it has been lowered inside the drain pipe to ensure a tight seal. The rubber gasket will receive 1-½" PVC, ABS, galvanized or other iron pipe sized piping like stainless steel or brass. The standpipe must not have an outside diameter greater than 2".
 
The 4" standpipe model is threaded, and takes 1-½" IPS pipe, galvanized, stainless steel, brass and ABS or PVC male adapters. The standpipe can be connected before or after the Drain Flood Protector's screws are tightened into the drain.  Be sure to highlight the location of each standpipe with bright tape, ribbon or something else - they can be difficult to see, and far too easy to walk into or trip over.

 

threaded standpipe for floodguard

 

Optional: Add a Pipe for the Drain Flood Protector (4" Standpipe Model).  This 12" long, PVC 1-½" IPS pipe is needed for the Drain Flood Protector (4" Standpipe Model FG-S-4F).  It will already be threaded on one end.  Save time on going to the store and buying pipe and cutting down to size.

 

**Note - if you don't get a snug fit, try adding this special rubber tape around the product.

 

 

 

View AllClose

Videos Hide Videos Show Videos

Related Products

Related Products

4" Float Model Flood Guard - check valve technology to seal off sewer water backing up in your floor drains Drain Flood Protector (4 inch Float Model)
Add to Cart

Drain Flood Protector (4 inch Float Model)

$33.95
The Drain Flood Protector works like a check valve to seal off water back-up caused by overloaded sewers.  Water will flow normally through the drain until the sewer begins to back up. Then...
FG-4F
Flood Guard Float Model for 2" Drain Drain Flood Protector (2 inch Float Model)
Add to Cart

Drain Flood Protector (2 inch Float Model)

$31.95
The Drain Flood Protector works like a check valve to seal off water back-up caused by overloaded sewers.  Water will flow normally through the drain until the sewer begins to back up. Then...
FG-2F
3" Flood Guard for basement flooding 3F Drain Flood Protector (3 inch Float Model)
Add to Cart

Drain Flood Protector (3 inch Float Model)

$32.95
The Drain Flood Protector works like a check valve to seal off water back-up caused by overloaded sewers.  Water will flow normally through the drain until the sewer begins to back up. Then...
FG-3F